• Physical Length: 702 mm (27.7 in.) Width: 417 mm (16.5 in.) Height: 618 mm (24.4 in.) Weight: 50 kg (110 lbs.) All figures include mounting yoke
  Dynamic Effects Color mixing: CMY, independently variable 0 - 100% Color wheel: 7 interchangeable colors + open Gobo wheel: 7 rotating gobos plus open, indexing, variable rotation Gobo animation wheel: Indexing, continuous rotation with variable angle, speed and direction Zoom: 10° - 44° (cut-off angles) Prism: Prism wheel with 2 interchangeable prisms, prism rotation and indexing Frost filter: Motorized, variable Dimming: 0-100% electronic Shutter: Electronic, strobe and pulse effects, instant open and blackout Focus: Motorized, variable 3 m (9.8 ft.) to infinity
  Control and Programming Stand-alone control: Up to 20 scenes with global fade/hold times Control options: DMX, RDM, standalone Configuration, addressing and status: Onboard control panel with OLED display or via RDM 8-bit control: CMY, color selection, gobo selection, prism, frost, animation 16-bit control: Gobo indexing and rotation, zoom, focus and intensity DMX channels: 20 DMX compliance: USITT DMX512-A RDM compliance: ANSI/ESTA E1.20
  Optics Light source: 440 W white light LED engine CRI (Color Rendering Index): 72 Color temperature: 6500 K (±250 K) LED lifetime: 20,000 hours (to >70% luminous output)* LED manufacturer: Appotronics Binning: Tight color and flux binning *Figure obtained under manufacturer's test conditions
  Photometric Data Cut-off angle: 10° - 44° Luminous intensity:

  At 10° zoom: 11,500 lumens
  At 16° zoom: 15,000 lumens
  At 40° zoom: 16,800 lumens

  Center Peak:

  At 10° zoom: 731,000 cd
  At 16° zoom: 311,000 cd
  At 40° zoom: 42,000 cd

  * All Photometric Data measured in steady state (30 minutes warm-up time) at 25°C ambient.

  Construction Housing: Cast aluminum Finish: Hard anodized, white or metallic grey lacquered Front glass: 5 mm (0.2 in.) anti-reflection coated tempered glass Ingress protection: IP66 Impact resistance: IK08 (with control panel display cover plate installed) Corrosion resistance: C5-M (very high corrosivity / marine, ISO 12944) Vibration resistance: 1.0g, Sinusoidal (IEC 60068-2-6)
  0,7g RMS Random (IEC 60068-2-64) EPA (Effective Projected Area): 0.28m²
  Gobos Suitable material: Metal or borosilicate glass, coatings heat-resistant to 450°C (842° F) Gobo diameter: 30.0 mm +0/-0.3 mm (1.2 in. +0/-0.02 in.) Maximum image diameter: 26 mm (1.02 in.) Gobo thickness, minimum: 1.1 mm ±0.1 mm (0.045 ±0.004 in.) Gobo thickness, maximum: 3.0 mm ±0.3 mm (0.118 in. ± 0.012 in.)* *Gobos thicker than 2.5 mm require a shorter spring in the goboholder
  Gobos and Color Frame
  Installation Mounting: Adjustable yoke Location: Suitable for wet locations. Do not immerse in water. Orientation: Any (sides must be kept vertical) Minimum distance to illuminated surfaces: 0.5 m (20 in.)
  Connections Power cable entry: IP66 cable gland Power connection: 1.8 m (5.9 ft.) cable tail with bare ends Power cable type: EU models: H07RN-F 450/700V, Ø10 mm US models: SJTW 14AWG, 300V, Ø9.3 mm Data cable entry: IP66 cable gland Data connection: 1.8 m (5.9 ft.) combined input + output cable tail with bare ends
• Electrical AC power: 100-120/200-277 V nominal, 50/60 Hz Power Supply: Auto-ranging electronic switch-mode Typical half-cycle RMS inrush current: 15.5 A Idle power (zero intensity, no effects applied): 75 W Surge protection: 4 KV
  Typical Power and Current 120 V, 60 Hz: 645 W, 5.5 A, PF 0.98 230 V, 50 Hz: 635 W, 2.9 A, PF 0.95 277 V, 60 Hz: 635 W, 2.6 A, PF 0.90 Figures are typical, not maximum. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.
  Thermal Cooling: Convection, internal forced air Total heat dissipation (calculated): 2350 BTU/hr. Maximum surface temperature: 85° C (185 ° F) Maximum ambient temperature (Ta max.): 45° C (113° F)* Minimum ambient temperature (Ta min.): -30° C (-22° F)**

  *Above this temperature, the fixture regulates output to protect from overheating.
  ** An integrated heat-element will heat-up internal components at ambient temperatures below 0° C (32° F) - For instant wake-up with no warm-up time, leave power applied constantly.
  

  Environmental RoHS: Compliant REACH: Compliant WEEE: Compliant Proposition 65: Compliant Efficacy (max output): 26 lm/W LWR*: 349 lm/kg (158 lm/lb)

  LWR = Lumen-to-Weight Ratio

  Approvals Global CB Certification/IECEE:

  IEC 60598-2-5 (IEC 60598-1)

  EU safety: EN 60598-2-1, EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493 EU EMC: EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61547 US safety: ANSI/UL 1598 US EMC: CFR 47 Part 15 Class A Canadian safety: CSA C22.2 No 250.0 Australia/NZ: RCM
  Included Items Silica gel desiccant bag: P/N 37220000 Two gobo retaining springs
  Related Items Martin Companion Cable:

  P/N 91616091
  Martin Companion Software Suite (including firmware uploader)

  Accessories Glare Shield, Exterior Projection 1000: P/N 91611768 Projection Setup Gobo, Exterior Projection 1000: P/N 91616075 Ring for gobo, OD30, set of 10 pcs: P/N MAR-91611851
  Spare Parts Silica gel desiccant bag in sealed foil pack: P/N 37220000 Goboholder for EP1000 with magnet incl. washer & short spring: P/N 50482185 Goboholder for EP1000 with magnet incl. washer & long spring: P/N 50482186
  Ordering Information EU models:

  Exterior Projection 1000, EU, Aluminum: P/N 90512000
  Exterior Projection 1000, EU, White: P/N 90512015

  US Models:

  Exterior Projection 1000, US, Aluminum: P/N 90512005
  Exterior Projection 1000, US, White: P/N 90512010

• 
  janvier 19, 2017
  Martin by HARMAN sponsor at IALD convention in Prague – the awesomeness of cutting-edge dynamic architectural lighting

From Live Shows to Landmarks: Spotlight on 8 Stellar Martin Pro Lighting Installs

Innovations in Architectural Lighting

HARMAN Creates 5-Star Experience at World’s Leading Hotels & Resorts

• Enregistrez votre Exterior Projection 1000
• Contacter l’assistance technique
• Centre d’aide 24/7