Width: 124.0 mm (4.9 in.)
Height: 40.0 mm (1.6 in.)
Depth: 124.0 mm (4.9 in.)
Weight: 0.5 kg (1.1 lbs.)

Control Protocols: P3, sACN, Art-Net and RDM over Art-Net
Protocol Detection: Automatic
Art-Net Compliance: Art-Net 1, 2, 3 and 4; including RDM over Art-Net
sACN Compliance: ANSI E1.31 - 2018
Martin P3 Compliance: P3 System Controller Software 6.1.0 or newer
Ethernet Transceiver IN: 100Mbit
Ethernet Transceiver OUT 1-2: 100Mbit
Firmware Update: not applicable

Split: Split a DCE line in two branches
Boost: Extend maximum cable length between two devices from 90 m to 2x 90 m

Split: Passive split of DCE 48 VDC input in two branches
Boost: None, system power limitations still apply

Power Status: 1x Green LED
Ethernet In Status: 1x Amber LED
Ethernet Out Status 1-2: 2x Amber LED

Color: Matte Black
Housing Material: Aluminium
Protection Rating: IP 66
NEMA Enclosure Rating: Type 3
Impact Resistance: IK 08
Corrosion Resistance: ISO 12944-6: 2018; C5 High, Test regime ISO 9227, 1440h
Vibration resistance: 1.0g Sinusoidal (IEC 60068-2-6) and 0.7g RMS Random (IEC 60068-2-64)

Orientation: Any
Wallmount: Flanges for installation on flat surface
Trussmount: Using half-coupler clamp in M10 threaded hole, max. bolt length 20 mm
Location: indoor or permanent outdoor

DC Power and Network input: 1x chassis-mount DCE hybrid connector (7pin)
DC Power and Network output: 2x chassis-mount DCE hybrid connector (7pin)
Max. distance between source (P3 PowerPort) or previous fixture and DCE DataSplitterBooster IP: 90 m
Max. distance between DCE DataSplitterBooster IP and following fixture or next DCE DataSplitterBooster IP: 90 m
Max. number of units in a daisy-chain: Unlimited, unless limited by power consumption
Surge protection: 4 KV
All connections hot plugging compatible

Nominal Input Voltage: 48 VDC +/- 10%
Power Supply Options: Martin P3 PowerPort 2000, Martin P3 PowerPort 500 IP Rental, Martin P3 PowerPort 500 IP Install, Martin DCE PSU 240 IP or generic 48 VDC PSU
Power Consumption
Typical: 0.5 W *
* Measurements made at nominal voltage. Allow for a deviation of +/- 10%.

Cooling: Convection
Maximum Ambient Temperature (Ta max): 55° C (131° F)
Minimum Ambient Temperature (Ta min): -30° C (-22° F)
Maximum Surface Temperature, steady state, at 40° C ambient: 55° C (131° F)
Typical Heat Dissipation (calculated, +/- 10%): 2 BTU/hr.

VDO Sceptron XB
Exterior Dot-1 Pro (via Exterior DC-Feeder)
Exterior Dot-4 Pro (via Exterior DC-Feeder)
Exterior Dot-9 Pro (via Exterior DC-Feeder)
Exterior Dot-HP Pro

1x Multi-Language Safety & Installation Manual

P3 PowerPort 2000: P/N MAR-90721200
P3 PowerPort 500 IP Rental: P/N MAR-90721201
P3 PowerPort 500 IP Install: P/N MAR-90721202
DCE PSU 240 IP: P/N MAR-90721203

Pre-Assembled Hybrid DCE Cables
DC + Ethernet Cable DCE-DCE 1m: P/N MAR-91700100
DC + Ethernet Cable DCE-DCE 2.5m: P/N MAR-91700101
DC + Ethernet Cable DCE-DCE 5m: P/N MAR-91700102
DC + Ethernet Cable DCE-DCE 10m: P/N MAR-91700103
DC + Ethernet Cable DCE-DCE 25m: P/N MAR-91700104

Bulk Hybrid DCE Cables
DC + Ethernet Cable 100m: P/N MAR-91700105
DC + Ethernet Cable LSZH 100m: P/N MAR-91700106

Field-Installable DCE Connectors
Field-installable Connector DCE Male: P/N MAR-91700107
Field-installable Connector DCE Female: P/N MAR-91700108

Closing Caps for DCE Connectors
Closing Cap Male DCE Connector: P/N MAR-91700109
Closing Cap Female DCE Connector: P/N MAR-91700110

Hybrid DCE Adapters
DC + Ethernet Adapter DCE Male-Male: P/N MAR-91700111
DC + Ethernet Adapter DCE Female-Female: P/N MAR-91700112
DC + Ethernet Adapter EtherCON+Wires to DCE: P/N MAR-91700113
DC + Ethernet Adapter DCE to EtherCON: P/N MAR-91700114

Rigging Accessories
Super Lightweight Half Coupler Rigging Clamp, black: P/N 91602018
Safety Cable, SWL 60 kg, BGV C1 / DGUV 17, black: P/N 91604006
Safety Cable, SWL 60 kg, BGV C1 / DGUV 17, silver: P/N 91604007

DCE DataSplitterBooster IP: P/N MAR-90721204