Ethernet Cable (discontinued)

With its large data-transmission possibilities and RDM/ACM in, Ethernet based product development is growing at a rapid rate. Therefore Martin has the pleasure of introducing its new, high quality ruggedized Ethernet cables and accessories – especially equipped for the Maxxyz network.

The new cables are designed and built to last in today’s tough touring environment and are intended to widen the usage possibilities and distance of the Maxxyz and the Ether2DMX box from fixtures.

Quality raw materials have created a very flexible cable with a cut resistant and durable wearing jacket- designed to withstand the extreme conditions of the professional touring segment; from frequent usage and coiling to constant weathering. The materials and design keeps the cables flexible and easy to handle in cold or hot applications , with their high chemical , oil , temperature, water, fungus resistance

Wear and tear resistant, the tough black colored polyurethane jacket ensures low friction, easy pulling and coiling and low memory, while strong Kevlar reinforcement and double shields secure tough stability and coverage of the data transmitting wires. The design is engineered to enable the cables can be used in reeling applications. All this gives you a professional, portable cable for the professional SSE segment.

CAT5E available cable with same physical structure below mentioned is available on request.

Maximum recommended length before requiring signal boost, (even with stranded conductors): 100 Mtrs.
Maximum coiling length:100 Mtrs.

Key selling points:
Stranded conductors ensuring high flexibility, low memory, little risk of conductor breakage and easy coiling up to 100 Mtr lengths.

PU jacket:
Black colored polyurethane providing low friction, easy pulling, UV,very good chemical and oil resistance. Cut and wear resistance under tough conditions.

Shields:
2 shield minimizing external influence and maximizing data protection. The extra braid shield aids mechanical strength and flexibility

Fillers and strength members:
Pair structure holding is constant and equalizes tension in the cable making it possible to use for reeling and constant coiling applications.

Product features:
26 AWG (0,14 mm2) bare stranded copper 7 x 0,16 conductors
Insulation: Color coded, polyethylene
Assembly: Pairs cabled with Kevlar strength member and tape wrapped
Shield – inner: Aluminum Mylar, 100% coverage
Shield – outer: Tinned copper braid, 80% coverage
Jacket: Polyurethane
Min. bending radius: 8 x outside Ø diam. mm,
Temperature: - 70 / 105 deg C
DC resistance: 15 ohms/100m at 20 deg C
Impedance: 100 +/- 15%
Capacitance: 4,6 nF \ 100 m
Capacitance unbalance: 340 pF/100m max. At 1KHz (wire to ground)
Insulation resistance: 150 M Ohm min.
Voltage rating: 230 VMS
Dielectric strength: 700 Vrms
Propagation delay (100 Mhz): 5,2 ns/m max at 100 Mhz
Delay skew: 20 ns/100 m max at 1-100 Mhz
Resistance unbalance: 3% max at 20 Deg C
Structural return loss (100 Mhz): 23 db/100 m min. at 1-20 Mhz
Diam, mm-outer Ø – nominal: 7,5 mm / 0,295”
Weight: 55 Kg / 1000 Mtr - 37 lbs/mft

Approvals:
IEC/ISO 11801, IEC 61156, EIA/TIA 568-B, ETL verified

Logistics:
Lengths in stock – ready made with NE8 MC/RJ45 male/male
Cross over cables: 2 Mtr lenghts
Straight cables: 5,10,25,50 Mtr lenghts
Straight cables - raw, open: 100 Mtr lenghts
Custom made lengths possible upon requests

Features

Support/FAQs

Ethernet Cable (discontinued)